Optimization of Laser Cutting Parameters toward Formation of Dross Defects on Stainless Steel Material

Imam Qulugqin Azhim; Rifelino; Syahril; Zainal Abadi

doi:10.24036/w7y55g34

Authors

Imam Qulugqin Azhim Universitas Negeri Padang
Rifelino Universitas Negeri Padang
Syahril Universitas Negeri Padang
Zainal Abadi Universitas Negeri Padang

DOI:

https://doi.org/10.24036/w7y55g34

Keywords:

Laser Cutting, Stainless Steel, Dross, Cutting Parameters, Analysis of Variance

Abstract

Laser cutting technology is widely used in the manufacturing industry because it is able to produce precise and efficient cutting. However, improper setting of cutting parameters can cause the formation of dross defects that reduce the quality of the cut. This research aims to analyze the formation of dross defects and determine the optimal cutting parameters on stainless steel materials with a thickness of 1 mm and a cutting length of 50 mm. The full factorial experimental design is used with three process parameters, namely cutting speed (S), focus point (F), and gas pressure (P). The height of the cutting results is measured and analyzed using the Analysis of Variance (ANOVA) method to evaluate the effect of each parameter on the observed response. The analysis results show that the focus point factor (F) has a significant effect on the dross height with a p-value of 0.029 (<0.05), while cutting speed, gas pressure, and all interactions between factors do not show a statistically significant effect. Contribution analysis shows that the F×P interaction gives the greatest contribution to the dross height variation of 29%, followed by the F factor of 27%. Based on the research results, the combination of optimal parameters to minimize the height of the dross was obtained at the focus point -2 mm, cutting speed 30 m/min, and gas pressure 10 bar. This finding shows that focus point setting is the main factor in controlling dross defects in the laser cutting process of stainless steel materials.

References

Adeniran, A., Olilima, J., & Akano, R. (2021). Analysis of Variance: The Fundamental Concepts and Application with R. International Journal of Mathematics and Computer Research, 9(10), 2408-2422.

Alsaadawy, M., Dewidar, M., Said, A., Maher, I., & Shehabeldeen, T. A. (2024). A comprehensive review of studying the influence of laser cutting parameters on surface and kerf quality of metals. The International Journal of Advanced Manufacturing Technology, 130(3), 1039-1074.

Antony, J. (2014). A Systematic Methodology for Design of Experiments. Design of experiments for engineers and scientists, 2, 33-50.

Bach, J., Zeuner, A., Wanski, T., Fischer, S., Herwig, P., & Zimmermann, M. (2023). Influence of the Dross Formation of the Laser-Cut Edge on the Fatigue Strength of AISI 304. Metals, 13(3), 624.

Callister Jr, W., & Rethwisch, D. (2020). Materials Science and Engineering: An Introduction (10th ed.). John Wiley & Sons.

Chryssolouris, G., & Salonitis, K. (2012). Fundamentals of laser machining of composites. Machining Technology for Composite Materials, 266-287.

Dundu, M. (2018). Evolution of stress–strain models of stainless steel in structural engineering applications. Construction and Building Materials, 165, 413-423.

García-López, E., Medrano-Tellez, A., Ibarra-Medina, J., Siller, H., & Rodriguez, C. (2018). Experimental study of back wall dross and surface roughness in fiber laser microcutting of 316L miniature tubes. Micromachines, 9(1), 4.

Girdu, C. C., Gheorghe, C., Redulescu, C., & Cirtina, D. (2021). Influence of process parameters on cutting width in co2 laser processing of hardox 400 steel. Applied Sciences (Switzerland), 11(13), 5998.

Günay, M., Yurtkuran, H., & Korkmaz, M. (2026). Multi-response optimization of fiber laser cutting parameters for improved cut quality and energy efficiency in ferritic stainless steel. Engineering Science and Technology, an International Journal, 79, 102420.

Jadhav, A., & Kumar, S. (2019). An experimental study on influence of process parameters on dross properties in laser machining of AISI 304 material. Journal of Manufacturing Engineering, 14(3), 111-116.

Ma, L., Wiame, F., Maurice, V., & Marcus, P. (2019). Origin of nanoscale heterogeneity in the surface oxide film protecting stainless steel against corrosion. npj Materials Degradation, 3(1), 29.

Prasad, K., & Chakraborty, S. (2014). A decision-making model for non-traditional machining processes selection. Decision Science Letters, 3(4), 467-478.

Riveiro, A., Quintero, F., Boutinguiza, M., del Val, J., Comesaña, R., Lusquiños, F., & Pou, J. (2019). Laser cutting: A review on the influence of assist gas. Materials, 12(1), 157.

Samarya, Y. T., Sulianti, M. M., Perangin-Angin, B., & Situmorang, M. (2013). Aplikasi laser CO2 untuk pemotongan (cutting) material menggunakan mesin cnc (control numeric computer). Saintia Fisika,, 5(1), 1-5.

Singh, A., Bal, K., Pal, A., Dey, D., & Roy Choudhury, A. (2021). A novel method to reduce dross in laser beam cutting of Ti-6Al-4 V alloy sheet. Journal of Manufacturing Processes, 64, 95-112.

Stoyanov, S., Petring, D., Piedboeuf, F., Lopes, M., & Schneider, F. (2023). Numerical and experimental investigation of the melt removal mechanism and burr formation during laser cutting of metals. Journal of Laser Applications, 35(4).

Sugiyono, A. (2019). METODE PENELITIAN KUANTITATIF, KUALITATIF DAN R&D.

Yang, K., & El-Haik, B. (2003). Design for Six Sigma : a roadmap for product development. McGraw-Hill.

Zhao, X., Li, Z., Yang, B., Sun, X., Sun, G., Wang, S., & Chen, C. (2023). Microstructure and mechanical properties of 304 stainless steel produced by interpass milling hybrid direct energy deposition-arc. Journal of Materials Research and Technology, 27, 3744-3756.